| |
*Award marks are B:Bachelor, M:Master, D:Doctor, G:General |
| Entry No |
Presentation |
Date |
Award |
Presenter |
Affiliation |
Paper Title |
Aug. 31 Poster presentations
Clock Tower Hall, 2nd Floor 18:00-20:00 |
| 2272 |
B5-P31-001 |
Aug. 31 |
|
Yong-Ming GUO |
Kagoshima University |
Modeling the Elastic-Plastic Micromechanical Response of the Particle Volume Fraction and the Average Size of Particles by Using 3-D FEM |
| 2605 |
B5-P31-002 |
Aug. 31 |
*D |
Yuji SATO |
Department of Mechanical Science and Bioengineering, Osaka University |
Theoretical prediction of glass forming ability of Cu-Zr alloys based on atomistic modeling |
| 2852 |
B5-P31-003 |
Aug. 31 |
*M |
Ryo FURUKAWA |
Graduate School of Science and Engineering, Doshisha University |
Corrosion behavior of UFG ZK60 magnesium alloy processed by ECAP |
| 2976 |
B5-P31-004 |
Aug. 31 |
*M |
Genki YAMAMOTO |
Graduate School of Science and Engineering, Doshisha University |
Corrosiveness of ultra -fine grained copper prepared by SSE method and effect of heat treatment |
| 2454 |
B5-P31-005 |
Aug. 31 |
*G |
Muhammad RIFAI |
Department of Mechanical Engineering, Faculty of Science and Engineering, Doshisha University |
High strength and super corrosion resistance of ultrafine-grained iron chromium alloy by equal channel angular pressing |
| 2618 |
B5-P31-006 |
Aug. 31 |
*G |
Qining SONG |
Hohai University |
Corrosion and cavitation erosion behavior of friction stir processed nickel aluminum bronze in salt water |
| 2399 |
B5-P31-007 |
Aug. 31 |
*G |
Nan XU |
College of Mechanical and Electrical Engineering, Hohai University |
Enhanced strength and ductility of large load friction stir welded CP-Ti joint associate with extremely low welding speed and rotation rate |
| 2795 |
B5-P31-008 |
Aug. 31 |
|
Jung-A LEE |
School of Materials Science and Engineering, Kyungpook National University |
Effect of different friction materials on the formation of secondary plateaus and friction properties in the brake materials |
| 2143 |
B5-P31-009 |
Aug. 31 |
|
Ming-yen LI |
Specialty Alloy Section, China Steel Corporation |
Effect of Microstructure Modifications on Tensile and Creep Rupture Properties of Ti-bearing Fe-Ni-Cr Superalloy |
| 3399 |
B5-P31-010 |
Aug. 31 |
*D |
Zhihui FENG |
School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing |
The influence of different position and direction of cast on the thermoplasicity of lean duplex stainless steel 2101 |
| 2423 |
B5-P31-011 |
Aug. 31 |
*M |
Jian Sin LI |
Department of Mechanical Engineering, National Taiwan Ocean University |
Thermal cycling on transformation and crystal orientation change of DSS |
| 2624 |
B5-P31-012 |
Aug. 31 |
*M |
Sukyoung HWANG |
Department of Material Science and Engineering, Kyoto University |
Microstructure and Mechanical Properties of 22Mn-3Si-0.6C Steel with Various Grain Sizes |
| 2557 |
B5-P31-013 |
Aug. 31 |
*M |
Yuki KITANO |
Graduate School of Science and Engineering, Doshisha University |
Improving formability of stainless steel pipe by Tube Channel Pressing |
| 3397 |
B5-P31-014 |
Aug. 31 |
*D |
Chengzhuang LU |
University of Science and Technology Beijing |
Effect of the differential speed ratio on surface ridging and texture development in ultra purified 17%Cr ferritic stainless steel |
| 2559 |
B5-P31-015 |
Aug. 31 |
*M |
Yuta YAMAGUCHI |
Graduate School of Science and Engineering, Doshisha University |
Deformation and recrystallization behavior of high-purity niobium for SRF cavity |
| 2780 |
B5-P31-016 |
Aug. 31 |
*G |
Nurul Hanis AZHAN |
Universiti Kuala Lumpur,Tokai University |
Ion-assisted Recrystallization Phenomena and the Growth of μm-sized Grains of VO2 Films in Biased Sputtering |
| 2808 |
B5-P31-017 |
Aug. 31 |
|
Daiki HATA |
Graduate School of University of Doshisha |
Influence of work hardenability on deformed structure and recrystallized texture after successive shear deformation (ECAP) |
| 3644 |
B5-P31-018 |
Aug. 31 |
*M |
Yuhei HAIZUKA |
University of Toyama |
TEM observation of HPT-processed Al-2.5Li(-2.0Mg) alloys |
| 2840 |
B5-P31-019 |
Aug. 31 |
*M |
Chika MORISHIMA |
Graduate school of Science and Engineering, Doshisha University |
Fabrication of ultrafine grained materials by novel SPD processing |
| 2848 |
B5-P31-020 |
Aug. 31 |
*M |
Kyosuke TADA |
Graduate School of Science and Engineering, Doshisha University |
Effects of grain size on tensile properties of nanocrystalline Ni fabricated by electrodeposition |
| 2384 |
B5-P31-021 |
Aug. 31 |
*M |
Ichiro KAWARADA |
Department of Material Science and Engineering, Kyoto University |
Effect of Grain Size and Alloying Elements on the Mechanical Properties of Magnesium Binary Alloy |
| 2547 |
B5-P31-022 |
Aug. 31 |
*G |
Yuichi HIGASHI |
National Institute of Technology, Kagoshima College |
Mechanical properties and plastic deformation behavior within extruded Mg96Zn2Y2 alloy joints welded by ultrasonic spot welding |
| 2550 |
B5-P31-023 |
Aug. 31 |
|
Masaaki RYO |
Faculty of Science and Engineering, Doshisha University |
High strength and high ductility of magnesium alloy (ZK60) by controlling microstructure using ECAP |
| 3627 |
B5-P31-024 |
Aug. 31 |
*D |
Yiran WANG |
State Key Laboratory for Mechanical Behavior of Materials, School of Materials Science and Engineering, Xi'an Jiaotong University |
The study on graphite coated with titanium by multi-arc ion plating |
| 2174 |
B5-P31-025 |
Aug. 31 |
*M |
Merita MERITA |
Doshisha University |
Nanocrystalline nickel dispersed with nano-scale WO3 by electrodeposition |
